Saturday, December 28, 2013

Preparing for Power: Installing the firewall mat, fuel tanks, pumps and filters.

As engine installation is looming near it is time to start getting the engine bay ready to accept its power plant. This includes the installation of some of the many restored components including the fuel tanks, fuel pumps, fuel filter, as well as some other ancillary components.

With lots to look at we will keep this a photo heavy post. Enjoy.

Here is the completed Fuel tank, pump, & filter assembly with all hoses and clamps installed. Close inspection of period photos confirmed without doubt that the fuel hoses were rubber on the outside and not cloth as is often fitted (and correct to later Ferrari's) during restorations.


Original Bendix design fuel pumps were sourced. These are identifiable by the manner that the wire comes out of the case which differs markedly from the newer electric Facet units. Another difference is in the internal design as these pumps make a distinctive clicking sound as they fill while the newer pumps just produce a steady whirr. Getting the right pumps was hard but will add to the period feeling with every engine start.


Correct Serflex Minus clamps were used throughout.


Another detail not overlooked was the wrapping of the wires between the fuel pumps and the chassis. Again period photos were referenced to get the wrap looking correct. Dino's used very few plastic tie wraps anywhere and where they did they were made by the company Colson. On the fuel pumps a singular Colson tie wrap is used to bundle the wires and it goes on the lower hose that joins the 2 pumps together.


The completed fuel tanks shown installed from the passenger side. Their full restoration was chronicled in previous blog posts.


Fuel tanks and firewall as seen from the drivers side



Close up of Alternator junction block. Later cars used a larger junction that contained 2 fuses while earlier cars used a junction without fuses that was riveted to the fiberglass firewall panel.


Again original Serflex hose clamps are used on the fuel tanks. The parts book shows these oriented horizontally but period photos show them vertically installed (as shown). We opted for vertical installation because it is factory correct and allows for easy access to check tightness when the engine is installed.


The fuel transfer pipe had its original SAIAG stamp faithfully reproduced and re-applied. The fuel drain plug was also safety wired in place as per factory delivery.

In many of the photos the firewall matting is visible. While later E series Dino's used an exposed aluminum firewall, earlier Dino's used a foam covering. This material has not been available from Ferrari in decades and was terribly fragile even when new. The original material was made up of soft open cell foam with a crusty and lightly textured outer coating encased in a mesh re-enforcement.

Through intensive research and extensive testing we were able to come up with a procedure to re-manufacture this firewall matting. The final result is nothing short of spectacular as our custom blend uses modern materials to produce a mat that is infinitely more durable and functional than original while maintaining a 100% concours correct look. It truly is the best of both worlds marrying function and form.

7 comments:

  1. Rob/Paul,
    Wiould you be able to supply me with the firewall matting that you have manufactured, as I suspect it's the same type of material used on my euro 328GTB ( even a sample of the firewall matting would be great ).
    BTW - looking great! - Thanks, Rocco. roccolocantore@rogers.com

    ReplyDelete
  2. Is your fuel tank cross over installed backwards? or is it different then the later models?

    ReplyDelete
    Replies
    1. Chris thank you for taking the time to point this out. Having referenced some other cars and the parts manual it is apparent that you are indeed correct. We have reversed the tube and re-printed the SAIAG marking on it. We do our best but mistakes are made from time to time so it is nice when a fellow enthusiast takes the time to help set us straight.

      Delete
  3. Awesome site as ever - I am interested that your tanks are painted a cream colour whereas mine are a goldy colour - which is right ? Great attention to detail - if you ever make that engine hood light fitting I would love to buy one - best Snowric

    ReplyDelete
    Replies
    1. Early gas tanks were cream while later ones were more golden in colour. For an M series car the cream is correct. What I do not know is how long it will stay in that colour once we start driving :) As for the engine light they will be advertised when finished as everything is on hold right now to complete the car

      Delete
  4. Good luck ! My UK M, sadly, has golden coloured tanks. Your car is awesome, I love the attention to detial around decals, markings on the jubilee clips etc. Snowric

    ReplyDelete
  5. When it comes to steel tanks, our manufacturing expertise sets us apart from the competition. As a trusted manufacturer, we specialize in crafting robust and long-lasting tanks that meet stringent quality standards. Our team of skilled engineers and technicians works diligently to ensure precise fabrication, from the initial design to the final product. Whether you need tanks for industrial processes, storage purposes, or specialized applications, we offer a comprehensive range of solutions tailored to your specific requirements. Count on us for reliable, high-quality steel tanks that deliver exceptional performance and durability.


    ReplyDelete